Deck railing and stair replacement swaps a loose, rotted or dated guard and stair for new ones built to current code, without rebuilding the whole deck. Louisville Decks replaces railings and rebuilds stairs for Louisville homeowners, with railing options in wood, composite, metal and cable. Short of new boards, it is the most visible change you can make to an older deck.
This work sits under our custom deck design and construction service, and the same rules apply whether the rail is new or a replacement.
What the code asks of a deck guard and stair
The International Residential Code, which Kentucky’s residential code is built on, sets the basics most inspectors check. Local amendments can change details, so the permit office has the final word.
| Item | General IRC requirement |
|---|---|
| When a guard is required | Walking surface more than 30 inches above grade |
| Guard height | At least 36 inches |
| Openings in the guard | A 4-inch sphere must not pass through |
| Stair riser height | No more than 7¾ inches |
| Stair tread depth | At least 10 inches |
| Handrail | On at least one side once a stair has four or more risers, 34 to 38 inches high |
| Single flight | No more than 151 inches of rise before a landing |
Our deck builder applies the same 30-inch line. Enter a deck height above 30 inches and the railing switches on and cannot be turned off; below that, railing is your choice.
Railing styles and what they cost
HomeGuide’s railing cost guide (November 2023) gives these ranges per linear foot:
| Railing | Per linear foot |
|---|---|
| Wood | $25 to $50 |
| Composite | $45 to $80 |
| Black metal | $55 to $110 |
| Cable | $80 to $180 |
Wire and cable infill keeps the view open, which matters most on a raised deck. The covered deck we built, a second-story deck under a gable roof, uses wire-panel railings, so from the deck you look out over the yard rather than at a row of balusters. Cable gives a similar view but needs re-tensioning over time. TimberTech and Trex both make railing lines designed to match their decking, and the materials page covers the decking side.
Replacing deck stairs
Stairs are often the first part of a deck to fail, because the bottom of the stringers sits on or near wet ground. A replacement stair gets new stringers, treads and risers laid out so every step is the same height, a pad at the bottom that keeps the stringers off the dirt, and handrails where the code calls for them. HomeGuide’s September 2025 figures put a 4- to 8-step flight at about $1,400 to $2,600.
On a tall deck, stair layout decides how much of the yard the stair takes up. The full stair on our second-story covered deck runs from the deck down to the yard, and on runs that long the 151-inch rise limit and the landing it triggers have to be planned from the start.
Fix the posts first
A guard is only as strong as its posts. Railing posts should be bolted through the deck framing with blocking behind them, not lag-screwed to the outside of a rim joist. If posts are rotted at the base or the rim joist is soft, that is a deck repair job before new railing goes on. If the boards are worn out too, pair the new rail with deck resurfacing so everything matches.
Call or text (502) 561-0375 to talk through your railing or stairs.
Questions homeowners ask about deck railing replacement
How much does it cost to replace a railing on a deck?
Multiply the railing length by the per-foot range for the style. HomeGuide’s guide runs from $25 to $50 a linear foot for wood up to $80 to $180 for cable. A 16-by-20 deck attached along its 16-foot side has about 52 feet of railing once you subtract a 4-foot stair opening.
What is the cheapest way to replace a deck railing?
Pressure-treated wood with wood balusters is the lowest-cost railing. Reusing existing posts saves money too, but only if they are solid at the base and properly bolted to the frame.
What can I use on my deck instead of railing?
If the deck is 30 inches or less above grade, the code generally does not require a guard, so planters, a step-down edge or built-in seating can mark the edge instead. Above 30 inches a guard is required, and a bench does not count as one.
What is the easiest deck railing to install?
Pre-made railing kits, composite or aluminum sections that fit between posts, go in fastest because the balusters come assembled. The posts still have to be anchored to the deck frame correctly, and that connection is the part that has to be done right.

